When injustice becomes law resistance becomes duty patch

We will give you the best service ever with a lot of benefit to you. Deliver to your home within days and give you some bonus point in your member card. Design by: shop Ethershirt. Halloween insane cat posse Shirt, Tank top, Hoodie, Sweatshirt. Fire department red horn pumpkin halloween Shirt, Long Sleeve, Sweatshirt.

Let me check my give a shit to meter nope nothing Shirt, Tank top, Hoodie, V-neck. Cat got your soul Shirt, V-neck, Sweat, Long sleeve. Demon panic at the disco shirt, hoodie, v-neck, tank top. Remember me Log in. Lost your password? Add to Wishlist. Categories: Halloween , politicial. Reviews 0 Description Reviews There are no reviews yet.

Long Sleeve Success will come to those who strive hard endless efforts It is also important to learn that people who grow up learning that stealing is okay and lying is fine and cheating is acceptable are all dynamics of those who possess the ability to physically harm animals or even people. A timely decision can mean life over death. I think it is important to keep the perspective that only 2, refugees from Syria have been resettled in the US — of a total of over 4,, The demands on the US in terms of resettling refugees is minimal in contrast to the demands on countries neighbouring Syria according to Amnesty , Lebanon is home to over a million Syrian refugees now, 1 in 5 people in the country.

It conflicts with current law — the Immigration and Nationality Act of banned all discrimination against immigrants on the basis of national origin, the immediacy of such a blanket ban violates the fifth amendment right to due process, and the 14th Amendment Equal Protection Clause. My Thoughts Exactly a week before this order was passed, millions marched in the streets standing for freedom and democracy.

James says this: 27 Religion that God our Father accepts as pure and faultless is this: to look after orphans and widows in their distress and to keep oneself from being polluted by the world. Because when injustice becomes law, resistance becomes duty. Did you know? My Saviour Himself was a refugee. But take heart! I have overcome the world. Like this: Like Loading Search for: Begin typing your search above and press return to search.

Press Esc to cancel. Follow Following. Sign me up. Already have a WordPress. Log in now. Loading Comments You really need to get rid of the bottom pour furnace, I have one and it's good for pistol size bullets but that's it. I mark my bullet with a piece of brass that I machined out to the o. I wanted the paper to stop on the bullet. I take the bullet stick it in the hole and give it a twist, it marks the bullet perfect.

What is the o. Thanks Stephen Borud. The Big 50 it's what's for death. What size casting furnace do you have? I have a 20lb. Lee bottom pour, and I find it works quite well for casting with a ladle. You also will have bottom pour capability for smaller bullets. I have also used an old Lee 10lb pot that I took the bottom pour mechanism off, and plugged the hole.

It works OK too, but is kind of small. With the 20 lb. Lee, I can cast around bullets at a time without adding alloy, and that is about enough for me to cast at one sitting.

After all the time spent casting so far the mould should have all the oil burned off by now. One problem is the big hole in the sprue plate. I dont know if Rick changed the plate since I got my mould from him but mine came with a. All that can be controlled with the alloy temp except maybe the wrinkles that is caused by a fast dump of alloy in the mould.

The swirl the alloy makes like pouring water in a glass to fast well the alloy hits the area just below the plate and sets while the base and the rest of the mould fills. Ricks moulds are vented very good but they dont do good when you dump the alloy in to fast, something that is hard to control with a bottom dump unless you adjust the flow rate to a lower volume.

With a ladle you start your pour with the mould cavity vertical and let most of the mould fill then slowly turn it vertical this will eliminate the swirl wrinkles. I had Rick make me a sprue plate with a. The main reason I want to use the small hole is two fold. Two to get rid of the parting lines and vent hairs. The mould is casting a very good quality bullet now with 2 tents total variance heavy to light.

Dumping more tim in the mix is not always the answer. The reason a dog has so many friends is because he wags his tail instead of his tongue. After incorporating several suggestions from here, along with a bit of intuition on my own, I've now cast some really nice PPBs. Higher casting temperature, faster pour, preheating the blocks--especially the base plug--three good cleanings before starting, and then finally finding the "sweet spot" of the pouring spout, and I'm in business.

Kurt: Yeah, I had lots of trouble with that big hole--that's why my comment about the sweet spot. I think I can cut down the volume of the pour now that I have several of the issues solved--for now, at least.