Emx88s manual

Using the digital effect Controllable parameter Variable range 0. In this example, an external effect such as delay or reverb is also being used. Q: Can a single speaker be connected to the mixer? When the device cools off, normal operation will resume automatically.

However, please check the following three points to prevent the problem from recurring. Page Specifications Master level control: nominal level, 1 channel level control: nominal level All channel level controls: minimum 1 channel level control: nominal level 10 kHz shelving 2. This manual is also suitable for: Emx88s. Print page 1 Print document 34 pages. Rename the bookmark. I have a the above mixer and it won't turn on all the time. There is power to the unit but the time delay to the power amp section won't kick in sometimes.

Once in awhile it comes on after 10 secs or so, other times an hour or so, sometimes never. All voltages are fine, preamp side works fine even when amp section won' t kick in. If I unplug the preamp from the amp the amp kicks in in the 10 sec time frame every time, no long delays. Just kind of wondering if anyone else has run into this problem and what the answer was. Tags: None. I have a customer with an all-tube pacemaker. His heartbeat is steady, reassuring and dependable, not like a modern heartbeat.

And if it goes wrong he can fix it himself. You can't do that with SMD. Both Hi-Z and Lo w-Z are balanced, and are com-. The nom-. Hi-Z jacks, and from —50 dB to —20 dB for the. Pin connections for the H i-Z and Low-Z jacks are. These two phone jacks ar e the input connect ors.

They are unbalanced, can be used simulta-. They can. Connect micr ophones to the MIC jacks. C onnect. The MIC. The MIC jacks are balanc ed, and are compatible. The LINE jacks are unbalanc ed, and are compati-. No minal input le v e l is —50 dB for the MIC.

Pin 1: ground Sleeve: gr ound. Pin 3: cold — Ring: cold —. Note: It is not possible to simultaneously use. For each channel, use only one of the. For this reason, dev ic es which do. The input of an exte r nal effect such as a dela y or. The nominal output level and impedance ar e. Y ou can connect a Y amaha FC5 foot sw itch sold. The Digital. Effect ON switch on the front panel must al ways. These are input jacks that allo w the sig nal from. If the effects processor has a ster eo output,.

If it has monaural output, use the A UX. Signal input to these. CD play er. The sig nals input to these jacks is. These are output jacks which send line lev el sig-. A stereo reco rding dev ice such as a cas-. The signals. R bus signal which has passed through the. Connect speak ers here. Ther e are three. At this time, use the power amp select switch N. Connect the included po wer cord t o this socket. Connect the plug of the power cor d to an A C out-. Connections W hen connecting various dev ices, make sur e the cables and plug s ha ve the correct rating.

Be sure to use cables designed for the purpose when you c onnect speakers to speak er jacks. The speaker impedanc e requirement varies depending on how y ou connect the speakers. Refer t o the dia-. Connect either one or two speak ers each to jacks A and jacks B. I f the power amp select switch is set t o MAIN.

For either setting of the sw itc h, use speak ers w ith an impedance in the range of 4—8 ohms if you are c onnect-. If you connect tw o speakers to each set of outputs, use speak ers w ith an impedance in the range of 8—16 ohms. The speak er w ill output the combined signal of the. A maximum output of W will be obtained when an 8-ohm speaker is used. When using two-channel connection or two-channel parallel connection, do not connect a speak er to the.

When using a bridge connection, do not connect a speaker t o either the A or B jacks. R emove this pr otective cap only when mak-. Adjusts the st ereo image of each channel using. Adjust the bal-. Note: When connecting a line level device to. Note: When turning the power off, reverse this.

Note: If the effect sound is distorted even if the. Using the digital effect Program Description. Parameter V ariable range. Re verberation simulating a spacious e xpanse. Re verb time 0. Re verberation simulating the acoustics of a small. Simulation of a plate re verb de vice. Produces a. Ideal re verb f or vocals.

Ideal echo f or vocals. Dela y time 0 — ms. Dela y effect that dela ys the signal. It lets you add depth to the sound, or create. Room size 0. Produces an eff ect as though two people were. Adds a sense of pitch to the tone.

Effectiv e on. Drive 0 — This eff ect sets the delay time to the interval at. The amount of. The LED will blink in synchronization with. Dela y time ms bpm —. A sound mix dif-. Note: You can connect a stereo playback device,. As a band PA In this example, an external effect. Although this example shows an external effects pro-. Note: If you are using an external effect, we rec-. If the external effect has a stereo output, it is. How e v er in this case, be sur e that the.

Installing an optional rack mount kit Never install the unit in a sealed. If you are going to install multiple devices includ-. U se a blank panel w ith holes. Y ou w ill need a 7U space t o install the rack. Afte r installation, the unit w ill project.

The following table describes the possible malfunctions of this dev ice, and the appropriate actions t o be taken in. Prob lem Cause Action. P ossible reasons f or the excessiv e load. Please wait. When the de vice cools off, normal. Howe ver ,. Y ou can refer to the peak le vel. Connections between de vices hav e. Quick Links. See also: Owner's Manual. Table of Contents. This document is printed on chlorine free ECF paper with soy ink. Previous Page. Next Page. Chapters Circuit Boards 23 Parts List It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.

Remove the seven 7 screws marked [80] and the screw marked [90]. Hold volume knobs and pull the front panel forward. Remove the screw marked []. The front panel assembly can then be removed. Page 15 [40], and the thirteen 13 screws marked [41], and the sixteen 16 hexagonal nuts marked [A]. Remove the front panel assembly.